Skip to main content
WATTMATRIX LAB BENCH // 230V 50Hz
☕
WILL POWER YOUR CPAP MACHINE230V AC
18.4HRS
Continuous: 40W
Surge Peak: 65W

≈ 2.3 nights (8h/night) · Safe motor start buffer (97.8% margin).

Ready to Run
Motor Start Margin+2935W Safe Buffer(65W Peak / 3000W Max)

How long will a Jackery Explorer 1000 v2 run a CPAP machine?

CPAP machine running (65 W max) and start-up (90 W max) draw fit the Jackery Explorer 1000 v2's 1,500 W continuous / 3,000 W surge ratings.

LOW LOAD
34.3HRS

humidifier and heated tube off (15 W)

15 W31.18 W net
TYPICAL SPECNOMINAL
18.4HRS

standard pressure with humidifier active (40 W)

40 W58.22 W net
HIGH LOAD
12.5HRS

high pressure with HumidAir and heated tube at max (65 W)

65 W85.34 W net
TELEMETRY // PRIMARY READOUT230V AC
CALIBRATED RUNTIME
18.4HRS

≈ 2.3 nights (8h/night)

NET PACK DRAW
58.22W

System standby power: 15W (25.8% of total draw)

CONTINUOUS_LOAD_UTILIZATION3% (40W / 1500W)
APPLIANCE_DRAW40W RUN / 65W PK
SOURCE_LIMIT1500W CONT / 3000W PK
SOLAR_RECHARGE (400W)3.52H (0.88D)
PARAMETER_SANDBOX // ENGINE v1.0.0

Live Load, Duty Cycle & Usage Simulator

40 W
MIN 7WNOMINAL 40WMAX 1500W
100%
5% INTERMITTENT50% CYCLING100% CONTINUOUS
8 h/night
1H / NIGHT8H OVERNIGHT24H CONTINUOUS
0 W
0W (OFF)200WMAX 400W
OUTPUT_PATH
TEMPERATURE DERATE
CONTINUOUS
18.4HRS
OUTAGE SPAN
2.3nights
AVG LOAD
40W
PACK DRAW
58.22W
Stack CPAP machine with other devices on Jackery Explorer 1000 v2 in the Load BuilderOpen Builder →
HARDWARE_INTERFACE // ELECTRICAL AUDIT

Jackery Explorer 1000 v2 × CPAP Machine Electrical Interface

1. AC RECEPTACLE & PLUG MATCH
BS 1363 / Europlug (230V 13A Domestic) → DIRECT FIT

Provides 3× CEE 7/3 (230V) (120V 60Hz).

2. WAVEFORM & THD SENSITIVITY
PURE SINE WAVE // THD-SENSITIVE LOAD

Pure sine wave inverter output. Safe for sensitive medical electronics and variable-speed motors.

3. STARTING SURGE (MOTOR INRUSH) MARGIN
65W TYP (90W MAX) VS 3000W LIMIT

Inductive motor/compressor load with 1.6× starting surge (motor inrush) (97.8% worst-case surge margin).

4. UPS SWITCHOVER & EXPANSION
UPS: UPS (20MS) · EXPAND: FIXED

Wall AC fast charge at up to 1200W (—m to 80%, 95m to 100%).

PHYSICS // TRANSIENT DRAW ENVELOPE

Dynamic Inrush Surge Curve (Locked Rotor Amps vs Steady State)

SAFE INRUSH HEADROOM (+2935W BUFFER)
0ms250ms500ms750ms1000ms0W2s Surge Limit (3000W)3000WContinuous Rating (1500W)1500WInrush (LRA): 65WRunning (FLA): 40W

Safe envelope verified: Starting surge (65W) remains comfortably below the 3000W surge trip line, with steady-state operation settling into the safe continuous zone at 40W.

LAB_RECORDS // EMPIRICAL OBSERVATIONS

Field Engineering Quirks & Operational Failure Modes

Hardware Bench Constraints (Jackery Explorer 1000 v2)
  • ›There's no voltage-reduction boost mode; Jackery's '50% Power Boost' marketing compares its 1,500 W output with the older 1,000 W model.
  • ›UPS: switches to battery within 20 ms with the AC charging cable connected and the AC output on. Jackery says it doesn't support 0 ms, advises against servers or workstations, and recommends testing first with one device.
  • ›Energy Saving Mode is on by default: if the AC load stays at or below 25 W, all outputs switch off after 12 hours. It can be turned off in the app.
  • ›Emergency charging (app-only) refills 0–100% in about 1 hour; Jackery's standard figure is 1.58 hours, and the manual says to use emergency mode only when necessary.
  • ›The Solar Lab held 1,560 W for 10 minutes, but the unit shut off within seconds at a sustained 2,200 W.
  • ›Solar input is two 8 mm DC8020 ports with a combined 400 W / 21 A limit.
  • ›The two USB-C ports are rated 30 W and 100 W.
Cycle Physics & Dwell Behavior (CPAP Machine)
  • ›Turning off the heated humidifier and ClimateLineAir heated tube cuts power draw by more than half (from 40–65 W down to ~15 W), more than doubling battery runtime.
  • ›Running from a power station's 12 V car socket via ResMed's Air11 DC/DC Converter (part 39231) avoids turning on the station's AC inverter and its ~15 W idle drain.
  • ›The AirSense 11 uses a 24 V DC input with a proprietary 3-pin sense pin, so it requires the official Air11 DC/DC converter rather than a passive 12 V barrel cord.
KNOWLEDGE_BASE // VERIFIED QA

Frequently Asked Questions: Jackery Explorer 1000 v2 & CPAP Machine

How long will a Jackery Explorer 1000 v2 run a CPAP machine?

About 18.4 hours on AC power, with the CPAP machine averaging 40 W (standard pressure with humidifier active (40 W)). The Jackery Explorer 1000 v2 then draws about 58 W from its battery, including 15 W for the inverter itself. Best case: about 34 hours (humidifier and heated tube off (15 W)). Worst case: about 12.5 hours (high pressure with HumidAir and heated tube at max (65 W)). At 8 hours a night, that's about 2.3 nights.

Is it better to run the CPAP machine from DC on the Jackery Explorer 1000 v2?

Yes. Using the ResMed Air11 90 W DC/DC Converter (part 39231) on the Jackery Explorer 1000 v2's 12 V car socket, the CPAP machine runs about 27 hours instead of 18.4 hours on AC, 49% longer, because it skips the inverter's conversion loss and its 15 W idle draw. That's 3.4 nights instead of 2.3 nights.

Why isn't the runtime just 1,070 Wh ÷ 40 W?

That simple division gives 27 hours, but the Jackery Explorer 1000 v2's inverter draws about 15 W whenever its AC outlets are on. At this light load that's 26% of everything the battery supplies, and inverter conversion losses take a further share. Jackery doesn't publish an idle figure and we haven't found an independent measurement, so this uses our 15 W estimate.

How long does the Jackery Explorer 1000 v2 take to recharge?

On wall power: about 95 minutes to full (Jackery figure). With its maximum 400 W of solar input connected, expect about 320 W in full sun, so a full recharge takes roughly 3.5 hours of full sun, so it can refill in a single day with 4 peak sun hours.

Can the Jackery Explorer 1000 v2 keep a CPAP machine running during a power cut?

It can act as a backup supply: with the CPAP machine plugged into the Jackery Explorer 1000 v2 and the Jackery Explorer 1000 v2 plugged into the wall, it switches the CPAP machine to battery in about 20 ms when the grid fails (Jackery calls this UPS mode).

AUDIT_LOG // DATA PROVENANCE & CITATIONS
NODE: jackery-explorer-1000-v2/cpap-machineSYSTEM HASH: 0xBB2C08772975VERIFIED TIMESTAMP: 2026-10-21T00:00:00Z
SOURCE_CITATIONS // JACKERY EXPLORER 1000 V2 (7)
LOAD_CITATIONS // CPAP MACHINE (3)