Skip to main content
WATTMATRIX LAB BENCH // 230V 50Hz
☕
WILL POWER YOUR CPAP MACHINE230V AC
2.3DAYS
Continuous: 40W
Surge Peak: 65W

≈ 7.0 nights (8h/night) · Safe motor start buffer (99.3% margin).

Ready to Run
Motor Start Margin+8935W Safe Buffer(65W Peak / 9000W Max)

How long will an Anker SOLIX F3800 run a CPAP machine?

CPAP machine running (65 W max) and start-up (90 W max) draw fit the Anker SOLIX F3800's 6,000 W continuous / 9,000 W surge ratings.

LOW LOAD
3.9DAYS

humidifier and heated tube off (15 W)

15 W41.17 W net
TYPICAL SPECNOMINAL
2.3DAYS

standard pressure with humidifier active (40 W)

40 W68.13 W net
HIGH LOAD
40.4HRS

high pressure with HumidAir and heated tube at max (65 W)

65 W95.12 W net
TELEMETRY // PRIMARY READOUT230V AC
CALIBRATED RUNTIME
2.3DAYS

≈ 7.0 nights (8h/night)

NET PACK DRAW
68.13W

System standby power: 25W (36.7% of total draw)

CONTINUOUS_LOAD_UTILIZATION1% (40W / 6000W)
APPLIANCE_DRAW40W RUN / 65W PK
SOURCE_LIMIT6000W CONT / 9000W PK
SOLAR_RECHARGE (2400W)2.11H (0.53D)
PARAMETER_SANDBOX // ENGINE v1.0.0

Live Load, Duty Cycle & Usage Simulator

40 W
MIN 7WNOMINAL 40WMAX 2000W
100%
5% INTERMITTENT50% CYCLING100% CONTINUOUS
8 h/night
1H / NIGHT8H OVERNIGHT24H CONTINUOUS
0 W
0W (OFF)200WMAX 2400W
OUTPUT_PATH
TEMPERATURE DERATE
CONTINUOUS
2.3DAYS
OUTAGE SPAN
7.0nights
AVG LOAD
40W
PACK DRAW
68.13W
Stack CPAP machine with other devices on Anker SOLIX F3800 in the Load BuilderOpen Builder →
HARDWARE_INTERFACE // ELECTRICAL AUDIT

Anker SOLIX F3800 × CPAP Machine Electrical Interface

1. AC RECEPTACLE & PLUG MATCH
BS 1363 / Europlug (230V 13A Domestic) → DIRECT FIT

Provides 6× CEE 7/3 (230V), 1× IEC Commando (32A), 1× Commando (16A/32A) (120/240V 60Hz).

2. WAVEFORM & THD SENSITIVITY
PURE SINE WAVE // THD-SENSITIVE LOAD

Pure sine wave inverter output. Safe for sensitive medical electronics and variable-speed motors.

3. STARTING SURGE (MOTOR INRUSH) MARGIN
65W TYP (90W MAX) VS 9000W LIMIT

Inductive motor/compressor load with 1.6× starting surge (motor inrush) (99.3% worst-case surge margin).

4. UPS SWITCHOVER & EXPANSION
UPS: UPS (20MS) · EXPAND: UP TO 26880WH

Wall AC fast charge at up to 1800W (120m to 80%, 150m to 100%).

PHYSICS // TRANSIENT DRAW ENVELOPE

Dynamic Inrush Surge Curve (Locked Rotor Amps vs Steady State)

SAFE INRUSH HEADROOM (+8935W BUFFER)
0ms250ms500ms750ms1000ms0W2s Surge Limit (9000W)9000WContinuous Rating (6000W)6000WInrush (LRA): 65WRunning (FLA): 40W

Safe envelope verified: Starting surge (65W) remains comfortably below the 9000W surge trip line, with steady-state operation settling into the safe continuous zone at 40W.

LAB_RECORDS // EMPIRICAL OBSERVATIONS

Field Engineering Quirks & Operational Failure Modes

Hardware Bench Constraints (Anker SOLIX F3800)
  • ›Split-phase 120V/240V output is native from a single unit without requiring a second paralleled station.
  • ›Equipped with an integrated NEMA 14-50R outlet capable of charging electric vehicles directly at up to 6,000 W (240 V, 25 A).
  • ›Features a true sub-20 ms uninterruptible power supply (UPS) switchover mode for servers and sensitive home office equipment.
Cycle Physics & Dwell Behavior (CPAP Machine)
  • ›Turning off the heated humidifier and ClimateLineAir heated tube cuts power draw by more than half (from 40–65 W down to ~15 W), more than doubling battery runtime.
  • ›Running from a power station's 12 V car socket via ResMed's Air11 DC/DC Converter (part 39231) avoids turning on the station's AC inverter and its ~15 W idle drain.
  • ›The AirSense 11 uses a 24 V DC input with a proprietary 3-pin sense pin, so it requires the official Air11 DC/DC converter rather than a passive 12 V barrel cord.
KNOWLEDGE_BASE // VERIFIED QA

Frequently Asked Questions: Anker SOLIX F3800 & CPAP Machine

How long will an Anker SOLIX F3800 run a CPAP machine?

About 56 hours on AC power, with the CPAP machine averaging 40 W (standard pressure with humidifier active (40 W)). The Anker SOLIX F3800 then draws about 68 W from its battery, including 25 W for the inverter itself. Best case: about 3.9 days (humidifier and heated tube off (15 W)). Worst case: about 40 hours (high pressure with HumidAir and heated tube at max (65 W)). At 8 hours a night, that's about 7 nights.

Is it better to run the CPAP machine from DC on the Anker SOLIX F3800?

Yes. Using the ResMed Air11 90 W DC/DC Converter (part 39231) on the Anker SOLIX F3800's 12 V car socket, the CPAP machine runs about 4.1 days instead of 56 hours on AC, 74% longer, because it skips the inverter's conversion loss and its 25 W idle draw. That's 12 nights instead of 7 nights.

Why isn't the runtime just 3,840 Wh ÷ 40 W?

That simple division gives 4 days, but the Anker SOLIX F3800's inverter draws about 25 W whenever its AC outlets are on. At this light load that's 37% of everything the battery supplies, and inverter conversion losses take a further share. The idle figure comes from Anker.

How long does the Anker SOLIX F3800 take to recharge?

On wall power: about 120 minutes to 80% and 150 minutes to full (Anker figures). With its maximum 2,400 W of solar input connected, expect about 1,920 W in full sun, so a full recharge takes roughly 2.1 hours of full sun, so it can refill in a single day with 4 peak sun hours.

Can the Anker SOLIX F3800 keep a CPAP machine running during a power cut?

It can act as a backup supply: with the CPAP machine plugged into the Anker SOLIX F3800 and the Anker SOLIX F3800 plugged into the wall, it switches the CPAP machine to battery in about 20 ms when the grid fails (Anker calls this UPS mode).

AUDIT_LOG // DATA PROVENANCE & CITATIONS
NODE: anker-solix-f3800/cpap-machineSYSTEM HASH: 0xD9410BD3BADCVERIFIED TIMESTAMP: 2026-10-22T00:00:00Z
SOURCE_CITATIONS // ANKER SOLIX F3800 (3)
LOAD_CITATIONS // CPAP MACHINE (3)