Skip to main content
WATTMATRIX LAB BENCH // 230V 50Hz
☕
WILL POWER YOUR STARLINK230V AC
30.7HRS
Continuous: 100W
Surge Peak: 120W

≈ 1.3 days (24h/day) · Safe motor start buffer (98.3% margin).

Ready to Run
Motor Start Margin+7080W Safe Buffer(120W Peak / 7200W Max)

How long will a Goal Zero Yeti PRO 4000 run a Starlink?

Starlink running (150 W max) and start-up (188 W max) draw fit the Goal Zero Yeti PRO 4000's 3,600 W continuous / 7,200 W surge ratings.

LOW LOAD
2.2DAYS

Gen 2/Gen 3 dish light browsing with snow melt off (50 W)

50 W75.95 W net
TYPICAL SPECNOMINAL
30.7HRS

Starlink Standard Gen 3 dish + Wi-Fi 6 router rated load (100 W)

100 W130.05 W net
HIGH LOAD
21.7HRS

active snow-melt heating and heavy throughput (150 W)

150 W184.29 W net
TELEMETRY // PRIMARY READOUT230V AC
CALIBRATED RUNTIME
30.7HRS

≈ 1.3 days (24h/day)

NET PACK DRAW
130.05W

System standby power: 22W (16.9% of total draw)

CONTINUOUS_LOAD_UTILIZATION3% (100W / 3600W)
APPLIANCE_DRAW100W RUN / 120W PK
SOURCE_LIMIT3600W CONT / 7200W PK
SOLAR_RECHARGE (3000W)1.75H (0.44D)
PARAMETER_SANDBOX // ENGINE v1.0.0

Live Load, Duty Cycle & Usage Simulator

100 W
MIN 25WNOMINAL 100WMAX 2000W
100%
5% INTERMITTENT50% CYCLING100% CONTINUOUS
24 h/day
1H / DAY8H OVERNIGHT24H CONTINUOUS
0 W
0W (OFF)200WMAX 3000W
TEMPERATURE DERATE
CONTINUOUS
30.7HRS
OUTAGE SPAN
1.3days
AVG LOAD
100W
PACK DRAW
130.05W
Stack Starlink with other devices on Goal Zero Yeti PRO 4000 in the Load BuilderOpen Builder →
HARDWARE_INTERFACE // ELECTRICAL AUDIT

Goal Zero Yeti PRO 4000 × Starlink Standard Electrical Interface

1. AC RECEPTACLE & PLUG MATCH
BS 1363 (230V 13A Irish Standard Plug) → DIRECT FIT

Provides 4× CEE 7/3 (230V), 1× IEC Commando (32A) (120V 60Hz).

2. WAVEFORM & THD SENSITIVITY
PURE SINE WAVE // THD-SENSITIVE LOAD

Pure sine wave inverter output. Safe for sensitive medical electronics and variable-speed motors.

3. STARTING SURGE (MOTOR INRUSH) MARGIN
120W TYP (188W MAX) VS 7200W LIMIT

Electronic/resistive load with 1.2× start-up profile (98.3% surge margin).

4. UPS SWITCHOVER & EXPANSION
UPS: UPS (10MS) · EXPAND: UP TO 19965WH

Wall AC fast charge at up to 1800W (120m to 80%, 150m to 100%).

PHYSICS // TRANSIENT DRAW ENVELOPE

Dynamic Inrush Surge Curve (Locked Rotor Amps vs Steady State)

SAFE INRUSH HEADROOM (+7080W BUFFER)
0ms250ms500ms750ms1000ms0W2s Surge Limit (7200W)7200WContinuous Rating (3600W)3600WInrush (LRA): 120WRunning (FLA): 100W

Safe envelope verified: Starting surge (120W) remains comfortably below the 7200W surge trip line, with steady-state operation settling into the safe continuous zone at 100W.

LAB_RECORDS // EMPIRICAL OBSERVATIONS

Field Engineering Quirks & Operational Failure Modes

Hardware Bench Constraints (Goal Zero Yeti PRO 4000)
  • ›Supports up to 4 Tank PRO 4000 expansion batteries, expanding total energy storage to nearly 20 kWh.
  • ›Equipped with high-power High Power Port (HPP) DC output delivering up to 30 A continuous at 12 V.
Cycle Physics & Dwell Behavior (Starlink Standard)
  • ›Setting Snow Melt to 'Off' in the Starlink app during a power outage keeps the dish heater from pushing continuous consumption up to ~150 W.
  • ›The Gen 3 Standard external AC power supply is rated up to 188 W (57 V DC output to the dish/router), and brief boot-up or heater transitions peak between 120 W and 188 W.
  • ›Enabling Starlink's scheduled Sleep mode overnight in the app cuts draw to near zero while no one is online, nearly doubling multi-day battery endurance.
KNOWLEDGE_BASE // VERIFIED QA

Frequently Asked Questions: Goal Zero Yeti PRO 4000 & Starlink Standard

How long will a Goal Zero Yeti PRO 4000 run a Starlink?

About 31 hours on AC power, with the Starlink averaging 100 W (Starlink Standard Gen 3 dish + Wi-Fi 6 router rated load (100 W)). The Goal Zero Yeti PRO 4000 then draws about 130 W from its battery, including 22 W for the inverter itself. Best case: about 53 hours (Gen 2/Gen 3 dish light browsing with snow melt off (50 W)). Worst case: about 21.7 hours (active snow-melt heating and heavy throughput (150 W)).

Why isn't the runtime just 3,993 Wh ÷ 100 W?

That simple division gives 40 hours, but the Goal Zero Yeti PRO 4000's inverter draws about 22 W whenever its AC outlets are on. At this light load that's 17% of everything the battery supplies, and inverter conversion losses take a further share. The idle figure comes from Goal Zero.

How long does the Goal Zero Yeti PRO 4000 take to recharge?

On wall power: about 120 minutes to 80% and 150 minutes to full (Goal Zero figures). With its maximum 3,000 W of solar input connected, expect about 2,400 W in full sun, so a full recharge takes roughly 1.8 hours of full sun, so it can refill in a single day with 4 peak sun hours.

Can the Goal Zero Yeti PRO 4000 keep a Starlink running during a power cut?

It can act as a backup supply: with the Starlink plugged into the Goal Zero Yeti PRO 4000 and the Goal Zero Yeti PRO 4000 plugged into the wall, it switches the Starlink to battery in about 10 ms when the grid fails (Goal Zero calls this UPS mode).

AUDIT_LOG // DATA PROVENANCE & CITATIONS
NODE: goal-zero-yeti-pro-4000/starlink-standardSYSTEM HASH: 0x11CA56E2CF03VERIFIED TIMESTAMP: 2026-10-25T00:00:00Z
SOURCE_CITATIONS // GOAL ZERO YETI PRO 4000 (2)
LOAD_CITATIONS // STARLINK STANDARD (2)